If you've been quoted a "lull" for your construction site and you're not sure whether that's different from a forklift, you're not alone — it's one of the most searched equipment questions among Singapore site managers. Short answer: a lull is a telehandler (it's a brand name that became generic, the same way "Xerox" became shorthand for photocopiers). The real comparison you need is telehandler vs forklift, and the right choice depends on your site conditions, reach requirements and load type.
What is a Telehandler?
A telehandler (short for telescopic handler) is a piece of lifting equipment with a single telescopic boom that extends forward and upward, similar to a crane arm but rigid. Forks are typically mounted at the end of the boom, though buckets, jibs and man-baskets can also be fitted.
Telehandlers are built for reach — both horizontal and vertical — on uneven or sloped ground, which makes them common on construction sites, agricultural yards and industrial sites where materials need to be lifted up and over obstacles (scaffolding, other equipment, partially built structures).
What is a "Lull"?
"Lull" is not a generic equipment category — it's the brand name of a telehandler manufacturer (Lull Industries, later part of JLG). In the same way people say "Kleenex" for tissue, "lull" is used informally across construction sites to mean any telehandler, regardless of manufacturer (JCB, Manitou, JLG, Merlo etc. are all commonly called "a lull" on Singapore sites).
So when someone asks "is a lull the same as a telehandler," the answer is yes — a lull is a telehandler, just referred to by a legacy brand name.
What is a Forklift?
A forklift (or fork truck) uses a vertical mast to lift loads straight up, with the load kept close to the machine's counterweight for stability. Forklifts are optimised for flat, stable ground — warehouses, yards, ports and factory floors — where the priority is fast, repetitive lifting and stacking rather than reach.
Key Differences
| Factor | Telehandler (Lull) | Forklift |
|---|---|---|
| Lifting mechanism | Telescopic boom (extends out and up) | Vertical mast (lifts straight up) |
| Reach | Horizontal and vertical reach, several metres forward | Minimal horizontal reach — load stays near the machine |
| Terrain | Rough, uneven, sloped ground | Flat, stable surfaces (paved, warehouse floor) |
| Typical capacity | 2.5T–5T (site-dependent) | 1.5T–72T across industry classes, not the RS Mech rental range |
| Common attachments | Forks, buckets, jibs, man-baskets, winches | Forks, clamps, rotators, side shifters |
| Operator position | Cab, often elevated visibility | Seated, lower to ground |
| Typical use case | Construction sites, placing materials at height or over obstacles | Warehouses, ports, yards, container handling |
When to Use a Telehandler vs a Forklift
Use a telehandler when:
- The site has uneven, sloped or unpaved ground
- Materials need to be placed at height or reached over an obstacle (e.g. lifting blockwork onto a scaffold platform)
- You need one machine to do both lifting and reaching, reducing equipment on a tight site
- The site is a construction or civil engineering project rather than a warehouse or yard
Use a forklift when:
- Ground is flat and stable (warehouse, yard, port, factory floor)
- You need high-volume, repetitive stacking or container handling
- Load capacity requirements are heavy (16T–72T class), which telehandlers generally don't match
- You're working in a confined indoor space where boom reach isn't needed
Can a Telehandler Replace a Forklift?
For light to medium loads on rough terrain, yes — many construction sites use a telehandler as their primary lifting machine and skip a forklift entirely. However, telehandlers are generally not built for the heavy capacity classes (10T+) that ports, shipyards and heavy industrial sites require, and they're less efficient for high-frequency palletised stacking work indoors. For those applications, a purpose-built forklift is still the better tool.
Licensing Requirements in Singapore
This is a common point of confusion. In Singapore, forklift and telehandler operation both fall under Ministry of Manpower (MOM) Workplace Safety and Health (WSH) requirements, but they are not automatically interchangeable certifications. A standard Forklift Operator Certificate (FOC) does not necessarily cover telehandler operation — operators should check with their employer and the equipment supplier whether additional training or a separate competency assessment is required for telehandler use, particularly where boom/jib attachments are involved. Always confirm certification requirements with MOM-approved training providers before deploying an operator on a telehandler.
RS Mech Fleet Context
RS Machinery & Engineering rents diesel forklifts from 1.5T to 23T, electric forklifts from 1.5T to 5T and reach trucks from 1.5T to 2.5T for operations across Singapore. The heavy diesel rental range is 7T–23T; confirm the actual unit and availability for your load and site. Higher-capacity industry examples in this guide do not describe our rental stock. For projects requiring boom reach or telehandler-specific capability, we can advise on the right equipment category for your site — get in touch to discuss your application.